




With Mud System Physics, rainy weather changes the way your equipment deals with the soil in Farming Simulator 25. The mod brings in a dynamic dirt system, so wheel behavior, surface grip, visual effects, cross-country driving ability, and the condition of fields and soil all respond to it. That gives you more to think about when you drive, work, or build through wet ground.
Features
- Humidity drives the dirt calculation in real time.
- Your wheels can slip, lose grip, and get stuck in mud.
- Heavy equipment faces a higher risk of getting stuck.
- Mud works differently across field soil types, and plowed fields are the most viscous.
- You can optionally remove vegetation in deep mud.
- Game menu settings let you:
- Switch the mud system on or off.
- Set the strength of the viscosity effect.
- Set the influence of rain.
- Set the visual effects.
- Set vegetation removal.
- Use more than 20 different knobs and switches.
- Use the tire puncture system and tire pressure system.
I prohibit using the mod code outside the system, as well as distributing it to other sites not via the author’s link.
Changelog
- V1.4.1.0
- Traction has been reworked, with rain and snow now calculated separately.
- The settings section has been simplified and moved into a new setup. Some elements were hidden and joined into one slider. You now get 3 separate road traction settings: normal, rain and snow.
- Wheel dirt formation has been adjusted. If you still run into problems, describe the complete sequence of actions and your settings in a private message.
- Stationary equipment in mud is checked less often.
- In fields with high humidity, mud buildup is now 15-fold faster.
- All bodies of water freeze and become ice in winter.
- Checks and iterations for all equipment connected to pressure and puncture debris have been significantly reduced.
- The mud color table is queried less often.
- When you use realDirtColor, the realDirtColor mod handles every color calculation exclusively. Without it, the dirt mod handles them exclusively.
- V1.4.0.0
- The mod settings now sit in a separate folder in
modSettings. Previously, they were simply saved inmodSettings. After the first load and save, you can deletemodSettingsMudSystemPhysics.xmlandMudSystemPhysicsHUD.xml, as well asMudSystemPhysicsNotices.xmlif it was present. - Turn on local moisture mode and water, or puddles, can appear in low-lying areas. More rain means more puddles, and they slowly dry once the rain stops. Do not run other flooding mods together with this mod, to avoid unnecessary processes in the game and possible visual issues.
- Local moisture mode has a much bigger performance impact. On large maps, local moisture calculations may cause FPS drops. You can enable this in the settings.
- Melting snow can add water to low-lying areas too. Puddles can freeze and thaw again, depending on the weather and temperatures.
- Soil drying on hills and slopes has been reworked for local moisture mode. Overall drying is approximately 2 times faster, and from May to September these values get an additional multiplier of 2 for faster drying during summer.
- Landscape and local mode processing code has been optimized.
FS25_realTireWear.zipby CobraModding contains stolen code presented as their own. You will not be able to play properly with it; delete it. It lowers your FPS. Use the originalFS25_Reifenverschleiss.zipmod by duestereLegende instead. Or do not use either of them at all.- ATTENTION: PUDDLE FORMATION WITH MOISTURE MODE ENABLED DIFFERS FROM WHEN THE MODE IS DISABLED AND IS A SIMPLIFIED VERSION. PUDDLES ARE SMALLER AND DRY FASTER, WHILE WITH LOCAL MOISTURE MODE, MUCH MORE DEPENDS ON THE LOCAL MOISTURE PARAMETERS THEMSELVES.
- The mod settings now sit in a separate folder in
- V1.3.9.0
- xXTennesieXx made the French translation.
- Keep the wheels spinning for long enough or make a sharp turn, and grass outside fields gets torn up, leaving a small patch of cultivated soil.
- When the turf breaks up, a short burst of dirt shoots out from under the wheel.
- A new toggle is available at “General” → “Turf damage”, and it is enabled by default.





